$83.69 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 315200792550
eBay 1.Fit For: 1997-2002 Ford Expedition 1997-2003 Ford F-150 2004 Ford F-150 Heritage 1997-1999 Ford F-250 2002 Lincoln Blackwood 1998-2002 Lincoln Navigator 2.Package Includes: 2x Front Lower Ball Joint -K8695T 1x Front Outer Tie Rod End – Driver Side -ES3366T 1x Front Outer Tie Rod End – Passenger Side -ES3367T 1x Front Upper Control Arm And Ball Joint – Driver Side -K8726T 1x Front Upper Control Arm And Ball Joint – Passenger Side -K8728T 2x Front Tie Rod Adjusting Sleeve -ES3368S Notes 8 Front Lower Control Arm Ball Joint Tie Rod For 1997-2002 Ford Expedition F-150 1.Fit For: 1997-2002 Ford Expedition 1997-2003 Ford F-150 2004 Ford F-150 Heritage 1997-1999 Ford F-250 2002 Lincoln Blackwood 1998-2002 Lincoln Navigator 2.Package Includes: 2x Front Lower Ball Joint -K8695T 1x Front Outer Tie Rod End – Driver Side -ES3366T 1x Front Outer Tie Rod End – Passenger Side -ES3367T 1x Front Upper Control Arm And Ball Joint – Driver Side -K8726T 1x Front Upper Control Arm And Ball Joint – Passenger Side -K8728T 2x Front Tie Rod Adjusting Sleeve -ES3368S Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Included Hardware : Mounting Hardware Custom Bundle : Yes Interchange Part Number : K8695T,ES3366T,ES3367T,K8726T,K8728T,ES3368S Superseded Part Number : ES3368S,car tie rod end replacement,outer tie rod end,rods ends OE/OEM Part Number : Suspension Control Arms and Steering Tie Rod Ends Linkages Cross Reference Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts Manufacturer Part Number : TA80128501P Adjustable : Yes Material : Alloy Steel Kit or Single Part : Kit Greasable or Sealed : Greasable OE Spec or Performance/Custom : OE Spec Surface Finish : Polished, Rust Protected Quantity : 8Pcs Items Included : Control Arm And Ball Joint, Ball Joint, Tie Rod End Discount Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales 2x Front Hood Lift Supports Shocks Struts For Dodge Ram 1500 2500 3500 4500 5500 USD 19.49 Upstream & Downstream Oxygen O2 02 Sensor For 2001-2005 Honda Civic 1.7L D17A7 USD 22.81 2 For Dodge Challenger 2008-2014 Keyless Entry Remote Control Car Key Fob USD 18.35 Throttle Body for Dodge Avenger Journey Caliber Jeep Patriot Compass 2.4L 2.0L USD 46.99 2x Front Hood Gas Lift Supports Struts Shocks Springs For Dodge Ram 02-10 4364 USD 17.69 Newly Listed 50x White 45-SMD T15/T10 Error Free LED License Plate Instrument Cluster Lights USD 47.89 Rear LH RH For Mercedes Benz E320 1996-2002 without Motor Window Regulator USD 38.77 Rear Passenger Side for BMW 323i 325i 328i 330i Power Window Regulator USD 23.89 20x White T10 / T15 45-SMD License Plate Instrument Panel Cluster LED Light USD 23.97 Rear Passenger Side Fits 1996-2002 Benz E320 Power Window Regulator w/o Motor USD 28.99 Terms & Contact Shipping Policy Payment Policy Return Policy FAQ About Us 8 Front Lower Control Arm Ball Joint Tie Rod For 1997-2002 Ford Expedition F-150 1.Fit For: 1997-2002 Ford Expedition 1997-2003 Ford F-150 2004 Ford F-150 Heritage 1997-1999 Ford F-250 2002 Lincoln Blackwood 1998-2002 Lincoln Navigator 2.Package Includes: 2x Front Lower Ball Joint -K8695T 1x Front Outer Tie Rod End – Driver Side -ES3366T 1x Front Outer Tie Rod End – Passenger Side -ES3367T 1x Front Upper Control Arm And Ball Joint – Driver Side -K8726T 1x Front Upper Control Arm And Ball Joint – Passenger Side -K8728T 2x Front Tie Rod Adjusting Sleeve -ES3368S Notes (1).Please check the fitment chart above before payment making sure all the suspension parts listed on this page are compatible with your automobile. (2).Please refer to Moog official website before narrowing down your search so as to avoid unnecessary item not as described return requests. (3).Please contact our customer services for targeted discount after all the items are received if you have reached any targeted discount thresholds, the terms of which is at the bottom of this page. If you are interested with any other suspension parts, please click and save our store. Ball Joint Replacement Guideline: If there is a knocking or clunking noise in the area of the front axle when the car is traveling over road bumps, potholes or curbs, then there is usually a defect in a component of the wheel suspension. Picture(A) The side of the front axle from which the (vibration) noise is emanating can already be determined during a test drive. The type of noise also already provides certain indications for maintenance regarding which components might be faulty. Picture(B) 1.Raise the vehicle and remove the front wheels. 2.To loosen the fastening screws and fixing nuts of the compression ball joint more easily, spray them with rust remover and allow to act for a few minutes. Picture(C) 3.Loosen the fastening screws of the broken ball joint on the control arm and remove the nuts. Picture(D) 4.Loosen and remove the fixing nut of the ball joint on the steering knuckle. Tip:If the ball stud rotates, hold the ball stud in place with a hexagon socket. Picture(E) 5.Remove the bad or worn ball joint from the control arm. 6.Loosen the compression ball joint on the steering knuckle using a suitable special tool. Picture(F) 7.Clean the cone connection. Tip:For better sealing and durability of the ball joint sleeve, a little silicone grease can be applied to the contact surface. Picture(G) 8.Insert new compression ball joint in the control arm and steering knuckle and tighten with new fixing nuts. 9.Reinstall front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. 10.Measure the chassis and adjust it using the various holes on the compression ball joint if necessary. 11.Finally, carry out a test drive. Sway Bar Stabilizer Link Replacement Guideline: While driving, the following signs may indicate a faulty sway bar stabilizer link: (1).Rattling and thumping noises on rough roads. (2).Imprecise vehicle handling. (3).Stronger inclination of the vehicle during cornering. If the sway bar stabilizer link is found to be defective, it should be replaced as described below. Picture(A) 1.Raise vehicle and remove front wheels. Tip:Always check both stabilizer links and replace them in pairs if necessary. 2.Spray fastening nuts of the stabilizer link with rust remover and let act for a few minutes. Picture(B) 3.Loosen the lower fastening nut of the stabilizer link at the stabilizer and remove. Tip:If the ball stud also starts to turn, hold it with a suitable tool. 4.Press stabilizer link out of torsion bar. Picture(C) 5.Loosen the upper fastening nut of the stabilizer link at the suspension strut and remove it. Tip:If the ball stud also starts to turn, hold it with a suitable tool. Picture(D) 6.Press stabilizer link at suspension strut out of bracket. Picture(E) 7.Insert new stabilizer link at suspension strut. Picture(F) 8.Tighten stabilizer link at suspension strut to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(G) 9.Insert new stabilizer link at stabilizer. 10.Tighten stabilizer link at stabilizer to the tightening torque specified by the vehicle manufacturer. Tip:Secure the ball stud against twisting with a suitable tool. Picture(H) 11.Remount the front wheels. Lower the vehicle and tighten the wheel studs to the tightening torque specified by the vehicle manufacturer. Tip:Even if replacing the stabilizer link does not directly affect the chassis setting, we recommend checking the axle setting and adjusting if necessary after working on the suspension. 12.Conclude with a test drive. Tie-Rod End Replacement Guideline: If you feel a bump in the steering when driving over road bumps or curbs, this might be due to worn tie rod ends or inner tie rods. Clicking noises during sudden steering movements can also be symptoms of a defective tie rod. In order to determine the exact cause and replace the defective tie rod, the car must be elevated with a vehicle lift in order to be examined more closely. This useful tip applies to the exchange of tie rod ends and inner tie rods, which together form the so-called tie rod. Picture(A) Note: Cleanliness is extremely important when working on the power steering. Incorrect work and contamination can lead to leakage and, in the worst case, to failure of the steering assistance. 1.Lift the vehicle and dismount the front axle wheels. 2.Spray the fastening nut of the tie rod end with rust remover and leave it on for a few minutes. Picture(B) 3.Dismount the front underride guard. Picture(C) 4.Loosen the fastening nut from the tie rod and remove it completely. 5.Remove the tie rod end from the steering knuckle using an appropriate ball joint separator. Picture(D) 6.Remove the clamp of the bellow on the steering gear. 7.Push the bellow towards the tie rod end. Picture(E) 8.Unscrew the inner tie rod from the rack. 9.Clean the sealing face of the bellow at the steering gear. Picture(F) 10.Clean the lug of the rubber contact surface of the ball joint in the steering knuckle. Note:Always use new self-locking nuts and bolts for a reliable repair. 11.Screw the new inner tie rod into the rack and tighten it with the tightening torque that has been specified by the vehicle manufacturer. Picture(G) 12.Mount the bellow and close the clamps with the appropriate special tool. Note:Incorrect mounting of the bellow can lead to corrosion of the rack: the steering gear starts leaking which can lead to a failure in the steering assistance. Picture(H) 13.Secure the ball joint in the steering knuckle and mount the nut. Please observe the tightening torque suggested by the vehicle manufacturer. Note:During mounting, the ball stud should not turn within the ball joint. This can cause damage inside the ball joint and can lead to early failure. Tip:Secure the ball stud against twisting with a suitable tool. Picture(I) 14.Mount the front underride guard. 15.Mount the front wheels and tighten them with the tightening torque recommended by the vehicle manufacturer. 16.Align the wheels and adjust them if necessary. Observe the vehicle manufacturer specifications. 17.Perform a test drive. Note:When performing the test drive, pay special attention to the handling while cornering and listen for possible noise emission. Frequently Asked Questions (1).Do I need to replace the control arm if the bushings are worn? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (2).What happens if a ball joint breaks? When a ball joint breaks, you will hear a mysterious noise inside your car wheel. Your car tire will wear-out since your alignment will be broken, and you will feel the car getting out of control. If the ball joint breaks completely, it can be separated, and things can turn sour quickly. The wheel will stop being nice and can even steer you off the road. It can be serious. Broken ball joints will seriously affect the steering and suspension. It can even result in your wheel falling off the car. (3).What happens if I don’t replace ball joints? If you don’t want to replace your ball joints, then get ready to experience some serious issues. The old ball joints cause mysterious clunking noise or drifting steering. Once they are worn-out, it will seriously affect your steering and suspension. However, you do not need to change the ball joints if it is new. (4).Do I need to grease new ball joints? I would say it will be a wise decision if you grease your new ball joints. At least I will always grease a new one after the installation. Greasing a new ball joint will make it stronger and extend its lifetime because there is a minimal amount of grease inside. I suggest you do so after the first installation. Follow the instruction card. (5).Why should I get my tie rods inspected on a regular basis? If you don’t get your tie rods inspected on a regular basis, there are some warning signs to watch (and listen) for. If your vehicle pulls to one side while driving, or when braking, it’s possible that bad tie rods may be the culprit. Your vehicle’s tires will also show uneven wear on the inside and outside edge of the tire when there’s a tire rod issue. However, one of the most noticeable signs of tie rods going bad will be a knocking sound coming from the front end of the vehicle when you turn into a parking space, or some other low speed, tight turning situation. (6).Vibrations One of the first symptoms that your tie rods are damaged or breaking is that the steering wheel will vibrate slightly. This is especially prevalent when you are speeding up or turning. This happens because the steering wheel is losing its control over the tires, causing the steering wheel to shimmy as you drive. (7).Shaking As the tie rods become further damaged, you will start to notice that the car itself will start to shake. This happens because the tires may start to wobble without you having full control over them. Although you should take your car into a mechanic at the first sign of tie rod problems, if you experience your car shaking you could be at risk for serious tie rod damage-which can cause accidents. Take your car into a mechanic if you experience this tie rod symptom. (8).Wandering If your tie rods continue to go unchecked or unfixed, the rods can completely break. This can cause you to lose all control of your car, possibly resulting in an accident. When this occurs, the car will may “wander” as you drive. At this point, the steering wheel will have no control over the tires and the tires will start moving independently, causing the car to drift while you are driving. If this happens while you are on a freeway or busy road, you and others could be at serious risk of an accident. If you experience wandering, stop your car, call a tow truck and take your car to the nearest mechanic. (9).What are the symptoms of a bad sway bar? Some of the common symptoms of a bad sway bar bushing or sway bar links going bad are: clunking noise, rattling noise, knocking uneven noise road, lack of stability when driving and noise going over speed bumps. poor handling during turns. (10).What happens when a sway bar breaks? Because a sway bar helps the car’s suspension to put more pressure on loaded springs, a broken sway bar means that the car’s suspension will not be able to handle corners as well or as quickly. While it is possible to drive with a broken sway bar, as a precaution do not take corners with excessive speeds. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Included Hardware : Mounting Hardware Custom Bundle : Yes Interchange Part Number : K8695T,ES3366T,ES3367T,K8726T,K8728T,ES3368S Superseded Part Number : ES3368S,car tie rod end replacement,outer tie rod end,rods ends OE/OEM Part Number : Suspension Control Arms and Steering Tie Rod Ends Linkages Cross Reference Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : topcn-autoparts Manufacturer Part Number : TA80128501P Adjustable : Yes Material : Alloy Steel Kit or Single Part : Kit Greasable or Sealed : Greasable OE Spec or Performance/Custom : OE Spec Surface Finish : Polished, Rust Protected Quantity : 8Pcs Items Included : Control Arm And Ball Joint, Ball Joint, Tie Rod End DiscountShippingWarrantyReturnFeedback Targeted Discounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means Topcn-autoparts won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Topcn-autoparts has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from Topcn-autoparts, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).Topcn-autoparts carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).Topcn-autoparts promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise Topcn-autoparts has the right to refuse any replacement requests. (5).Topcn-autoparts promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise Topcn-autoparts has the right to refuse any replacement requests. (6).Topcn-autoparts carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).Topcn-autoparts has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of Topcn-autoparts. All rights reserved.
Frequently Asked Questions About 8 Front Lower Control Arm Ball Joint Tie Rod For 1997-2002 Ford Expedition F-150 in My Website
rivieracharters.rentals is the best online shopping platform where you can buy 8 Front Lower Control Arm Ball Joint Tie Rod For 1997-2002 Ford Expedition F-150 from renowned brand(s). rivieracharters.rentals delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling 8 Front Lower Control Arm Ball Joint Tie Rod For 1997-2002 Ford Expedition F-150 on rivieracharters.rentals?
rivieracharters.rentals helps you to shop online and delivers Prada to your doorstep. The best-selling Prada on rivieracharters.rentals are: PRADA SUNGLASSES WOMENS AUTHENTIC KENDALL JENNER SUMMER BLACK FASHION HAILEY NYC PRADA Logo Avio Denim Large Canapa Tote PRADA Handbag BRW PRADA LINEA ROSSA 01S Matte Black Grey Gradient Sport Sunglasses PS01SS Unisex PRADA Tote Bag Nylon Purple Auth 85052 PRADA Venice Print Top Handle Tote Bag Blue Canvas x Leather Used with Pouch PRADA Tote Bag Nylon Khaki Auth 73455 PRADA Shoulder Bag Nylon Khaki Auth bs10312 PRADA Hand Bag Nylon Purple Auth 83954 PRADA Shoulder Bag Leather Silver Auth ep4586 PRADA Paradoxe EDP 1.2ml / 0.04 oz Spray Vial x 10 PCS *NEW* PRADA 2Way Bag Logo Metal Fittings Ribbon Gold Nylon Pink PRADA Shoulder Bag Nylon Orange Auth 82569 PRADA SYMBOLE Black White Color Block Triangle PR24ZS 24Z Fashion Sunglasses NEW PRADA VPS 51N 5AV-1O1 SILVER HAVANA BLACK AUTHENTIC EYEGLASSES W/CASE 51-20 PRADA PR 19ZS 1425S0 White Talk Grey Women’s 55 mm Sunglasses Prada 0PR09WS 1AB5Z1 54mm Polarized Black Sunglasses PRADA Tote Bag Nylon Green Silver Auth 86347 PRADA Tessuto City Nylon Tote Bag Pink Ombre PRADA Canapa GM Hand Bag Canvas 2way Light Blue Auth 87668 PRADA Women’s Shoulder Bag Hobo Tessuto Nylon Leather Black Used Authentic F/S PRADA Hand Bag Nylon Black Silver Auth bs17912 PRADA Shoulder Bag Nylon Khaki Auth 70209 PRADA Handbag Leather BRW PRADA Shoulder Bag Nylon Beige Auth 75615 PRADA Sports Hand Bag Canvas White Black Silver Auth 91239 PRADA Tote Bag Nylon Khaki Auth 76804 PRADA Hand Bag Nylon Navy Auth hk867 Authentic PRADA Nylon Tessuto Leather Shoulder Hand Bag Khaki Green 2377L Prada Grey Leather Double Handle Tote PRADA Les Infusions De Iris Body Lotion . sz: 100 Ml /3.4 oz New in box Auth PRADA Logo 2Way Hand Bag Purple Nylon Saffiano Leather B2052A Used PRADA Tote Bag Nylon Green Auth bs12869 PRADA Hand Bag Satin Purple Auth 82240 Prada Logo Triangle RED Badge Pendant clothing emblem Cheapest + Freebie PRADA Fringed nappa leather shoulder bag 1BG541 black Women Shoulder Bag PRADA Shoulder Bag Leather Purple Auth 68014 PRADA Hand Bag Nylon Orange Auth 74418 PRADA Tessuto Nylon Pouch Beige Small Handbag Authentic Prada Black/White Canvas Small Canapa Logo Tote PRADA Tote Bag Canvas Beige Auth yk11521 PRADA Shoulder Bag Nylon Khaki Auth 80866 *SPS 53N (2x Pairs) Nose Pads for Prada Sunglasses Replacement Nosepads PS 53NS PRADA Hand Bag Nylon Pink Auth hk1377 PRADA Tote Bag Leather Black Silver Auth 91249 4 Pcs Set Prada Candy Kiss, Gloss, L’eau, Florale Samples RARE Set from Spain PRADA Handbag Leather CML Prada Women’s Nylon,Leather Backpack Khaki Brown BF568573 PRADA Shoulder Bag Canvas Brown Auth 79327 Prada Black 2way Handbag BN2567 180 XX91536 PRADA Chain Shoulder Bag Nylon White Gold Auth 44147 PRADA Shoulder Bag Nylon Black Auth 69689 PRADA Shoulder Bag Nylon Black Auth fm2662 Auth PRADA Logo 2Way Tote Bag Shoulder Bag Brown Leather BR5033 Used PRADA Hand Bag Nylon 2way Silver Gray Auth 89250 PRADA Shoulder Bag Nylon Beige Auth 83490 Prada White Nylon Handbag Metal Handle Triangle Authentic PRADA Tote Bag Nylon Turquoise Blue Auth 73880 Auth PRADA Shoulder Bag Pouch Black Nylon Leather 1M1187 Used PRADA PR 07ZV 18D1O1 Baltic Marble Demo Lens 55 mm Men’s Eyeglasses $405 PRADA Hand Bag Nylon Black Auth yk14098 PRADA Shoulder Bag Nylon Black Auth bs13422 PRADA Shoulder Bag Nylon Black Auth yk13259 Prada Paradoxe Eau De Parfum Sample Vial Size Perfume 0.04 fl oz Sealed The Devil Wears Prada musical Playbill Chicago preview pre-Broadway Elton John PRADA Tote Bag Nylon Purple Orange Auth bs6261 Build Your Dvd Collection U PICK $.99 DVD MOVIE cheap 4! PRADA Shoulder Bag Nylon Purple Auth yk12728 Auth PRADA – Light Brown Leather Shoulder Bag PRADA Shoulder Bag Canvas Beige Auth ac2628 Black P R A D A Milano T-shirt Jersey Tee Shirt PRADA Accessory Pouch Nylon Black Auth 37131 VINTAGE AUTHENTICATED PRADA Sound Beige Leather Hobo Shoulder/Handbag #7 PRADA Shoulder Bag Nylon Light Blue Auth 78258 PRADA Tote Bag Nylon Leather Blue Gold Auth 91252 Product Prada Large Embroidered Logo Shoulder Tote Bag Illustration PRADA Nose Pads W/Screws for Sunglasses Eyeglasses Clear Gold Prada 17mm GENUINE Women Designer Perfume Vials Samples Choose Scents, Combined Shipping & Discount Authentic PRADA Logo Leather Ribbon Shoulder Bag Green BP0166 Used F/S PRADA Hand Bag Nylon Silver Beige Auth 84643 Authentic PRADA 1TT119 pouch #246-000-410-1741 PRADA Pouch Canvas Beige Auth ac3148 PRADA Sports Hand Bag Nylon Gray Auth bs15816 PRADA Nose Pads for Sunglasses Eyeglasses Black W/Screws Size 17mm Large Genuine PRADA Hand Bag Nylon Black Auth 68086 PRADA Hand Pouch Nylon Pink Auth 87684 PRADA Shoulder Bag Nylon Leather Khaki Auth 83398 Prada Tessuto Triangle Logo Plate Black Nylon/Leather Shoulder Bag Women’S PRADA Shoulder Bag Nylon Black Gold Auth 87028 PRADA Tote Bag Patent Leather BRW Auth PRADA Nylon Leather Ribbon Hand Bag NERO Black BN1601 Used PRADA Vitello Daino Pebbled Leather Slouchy Bag Tote Blue Gold Carry All Cobalto PRADA Shoulder Bag Nylon Black Silver Auth bs16713 PRADA Shoulder Bag Nylon Black Auth 79556 PRADA Hand Bag Nylon Ivory Auth 48756 PRADA Shoulder Bag Nylon Cream Auth 69655 PRADA Nose Pads for Sunglasses Eyeglasses Black Silicon 15mm With Screws Genuine PRADA Pouch Satin Silver Auth 74688 Prada Tan Cervo Sacca 2 Manici Shoulder Bag PRADA PR 16WS White/Grey GRADIENT LENSES 53/20/142-130 Sunglasses ITALY MADE NEW Mens Pullover Fleece Hoodie
